Flush floor Trunking

Flush floor trunking is used to supply power, data services within office accommodation with a minimum screed depth of 75mm, to accept a maximum system depth of 70mm.

Supplied in standard 2 metre lengths in three or four compartment options.

A predetermined grid design incorporating the position of the trunking and junction boxes is required for direct fixing to a ribbon screed 15mm thick. During the main screeding operation it is essential to have the cover sections fitted to prevent both ingress and distortion of the trunking side wall.

Once screeded, service outlet boxes may be fitted in any position on the system simply by removing the 333mm long cover and internal separator. The service box is then located using the existing fixings. Service boxes cannot be located in junction box positions.

Trunking
pre galvanised to BSEN10143:1993
Formerly BS2989

Finish:
Self colour

Service outlet box:
pre galvanised to BSEN10143:1993
Formerly BS2989

Finish:
Powder coated
gray - RAL 7015

 Non standard sizes,
profiles and finishes are
available to order

 

Shallow flush floor trunking    modular
 
Width mm Depth mm Thickness body mm cover mm   Two Compartment Three Compartment
150 25 1.25   2.0     SFL 21      -    
225 25 1.25   2.0     SFL 22     -    
225 25 1.25   2.0      -       SFL 23  
Spare connector kit
 
Width mm Depth mm Thickness body mm cover mm   Two Compartment Three Compartment
150 25 1.25    -     SFL 81      -    
225 25 1.25    -     SFL 82     -    
225 25 1.25    -      -       SFL 82  
Conduit outlet plate
 
Width mm Depth mm Thickness body mm cover mm   Two Compartment Three Compartment
150 25  -   2.0     SFL 51      -    
225 25  -   2.0     SFL 52     -    
225 25  -   2.0      -       SFL 53  

 

90 riser bend  
             
Width mm Depth mm Thickness mm Two Compartment   Three Compartment
150 25 1.25 SFL 41      -
225 25 1.25 SFL 42     -
225 25 1.25  -   SFL 43
End stop
             
Width mm Depth mm Thickness mm Two Compartment   Three Compartment
150 25 1.25 SFL 71      -    
225 25 1.25 SFL 72     -    
225 25 1.25  -       SFL 72  

 
Base entry skirting unit
                   
Width mm Depth mm Thickness mm Two Compartment   Three Compartment   Skirting catalogue number
150 25 1.25 SFL 91      -     SA 12  
225 25 1.25 SFL 92     -     SA 15  
225 25 1.25  -       SFL 93   - 16
The unit will be supplied for use with the skirting system as shown in the table unless otherwise specified.

 

Junction box
                   
Width mm Depth mm Thickness body mm cover mm   Two Compartment   Three Compartment
150 25 1.25   2.0     SFL 31   -    
225 25 1.25   2.0     SFL 32   -    
225 25 1.25   2.0     -     SFL 33
Junction boxes are supplied completewith flyovers and a 3mm recessedcover.

 

Service outlet box
                   
Width mm Depth mm Thickness body mm cover mm   Two Compartment   Three Compartment
150 25 1.25   2.0     SFL 926   -    
225 25 1.25   2.0     SFL 929   -    
225 25 1.25   2.0     -     SFL 939
Service outlet boxes are supplied without outlet plates - refer to page 27 for the full range.

Note:
Outlet plates FSB 010, FSB 020 andFSB 030 cannot be used with theshallow flushfloor service outlet box when power socket are fitted.